A-JOINT® TRAFFIC is a heavy-duty paving grout specially developed for public areas. It is designed for traffic loads of up to 40 t, is sweeper-suction machine resistant and at the same time frost and de-icing salt resistant.

Thanks to its high flowability and self-compacting properties, A-JOINT® TRAFFIC can already be used for joints from 5 mm. Thanks to its rapid curing, the grouted surface can be walked on after just 6 hours and driven on after 24 hours. From new grouting to the renovation of existing surfaces, A-JOINT® TRAFFIC can be used universally and reduces maintenance costs and the risk of accidents caused by loose stones.

A-JOINT® TRAFFIC is particularly suitable for highly frequented squares, public roads and paths as well as for use in paved street gutters.

neutral
stone grey
basalt

Properties

  • Sustainable, weed-free joint solution up to service class N3 with fast traffic release
  • For joint widths from 5 mm
  • For joint depths from 30 mm
  • High strength and self-compacting
  • Can be used in drizzle and soil temperatures from 0°C
  • No cement haze, very low water consumption during application
Consumption calculator

Processing instructions:

Preparing the site 
The joints must be cleaned of weeds, roots and loose parts and cleared to a depth of at least 30 mm or, in case of traffic load, to 2/3 of the stone height. The surface to be grouted must be free from all dirt. Adjacent areas that are not to be grouted should be masked or covered. To avoid settling and loose stones, we recommend a permanently water-permeable and load-bearing substrate corresponding to the subsequent load (pay attention to the current standards and guidelines). We generally recommend the bonded construction method.

Pre-wetting:
Thoroughly pre-wet the entire surface. Higher floor temperatures and absorbent, open-pored stone require more intensive pre-wetting. Generally, clean and cold water should be used.

Mixing:
Open the bag and pour the sand into a suitable mixing container. Completely add the contents of the separately supplied bottle containers. Fill the emptied bottles with 0.5 litres of water each and close them, shake vigorously and add to the mixture. Ensure that the bottles are completely empty. Use a professional stirrer or mixer. Start the mixing process. After 3 minutes mixing time, add a further 2.0 litres of water and mix thoroughly for another 3 minutes until a creamy, flowing mixture is obtained. 

Filling the joints:
Pour the finished mixture onto the pre-wetted surface. Work in the joint compound carefully and as diagonally as possible to the joint using a rubber squeegee. Keep the surface constantly wet during this work.

 

Cleaning the surface: 
After approx. 10-20 minutes, sweep the stone surface carefully and diagonally to the joint, using a medium-coarse street broom. If white gel-like streaks form on the stone surface, the correct sweeping time has not yet been reached. Then remove the remaining mortar residues with a fine coir broom. Swept-off material is not to be used again. Make sure that chamfers (beveling of the side edges) on slabs and pavers must be exposed.

Follow-up treatment:
Protect the freshly grouted surface from rain for 12-24 hours. We recommend using construction foil or tarpaulins as rain protection. To allow sufficient air to circulate, the rain protection must not be placed directly on the surface. At temperatures around 20°C, the surface can be walked on after 6 hours and driven on after 24 hours. A strength test is recommended before use. Cleaning work may be carried out after 7 days at the earliest.

Important

Resin film: After grouting with A-JOINT® TRAFFIC a thin resin film remains on the stone surface, which intensifies the stone colour and protects the stone from dirt. This resin film usually disappears over time due to weathering and use of the surface. If in doubt, create a small test area. The synthetic resin film is not a design defect, as neither the quality nor the functionality of the joint is affected.

Application notes: Use A-JOINT® TRAFFIC only with a stable, load-bearing and permanently water-permeable substructure or a slope of at least 2%. The application is only recommended in well ventilated areas. Please wear adequate protective clothing. Tools should be cleaned with water during and after application.

Regularly remove dirt, leaves and moss from the joint surface. 

All fillers are natural products and are subject to natural colour variations. Our information is based on years of experience and the current state of the art, but is non-binding and does not constitute a contractual legal relationship.

en_GBEnglish
A-Joint